Our Products

Pro-Bed 2000 Stock Bedding Epoxy

Pro-Bed 2000
The Ultimate Stock Bedding Epoxy

       Epoxy or glass bedding has been popular for many years as a tool for accurizing rifles of all types.  Accuracy depends on shot-to-shot consistency.  A great deal of a rifle’s ability to achieve this consistency is dictated by the relationship of the metal and the stock.  During the firing process a great deal of recoil or kick is created which tends to shift the barrel and action in the stock.  This change dramatically affects the rifles ability to achieve shot-to-shot repeatability.  In order to achieve extreme accuracy, we need to go beyond just good fit.  We need to manage vibration cycles.  In nature all things vibrate and in order for a rifle to achieve extreme repeatability we must minimize the vibration cycles and make them as consistent as possible.  Once again we are back to the stock-to-metal fit.  Pro-Bed 2000 epoxy is the best tool available to meet that requirement.  There have been a number of epoxy products used by the gunsmithing fraternity over the years and almost all of them were not designed for the sole purpose of accurizing rifles.  Pro-Bed 2000 was formulated by a gunsmith with over 20 years of professional experience in epoxy bedding rifles.  Pro-Bed 2000 directly addresses every problem unique to epoxy bedding.

Complete Epoxy Bedding System.

Complete system contains epoxy resin either black or brown, Professional grade mold release, fumed silica for thickening, modeling clay for plugging pi holes an mixing sticks

_MG_0662

Basic Kit.

The Basic epoxy kit contains Pro-Bed 2000 epoxy resin only, either black or brown.

_MG_0666

Ease of mixing: A non-critical mix ratio of 1:1 by volume insures that Pro-Bed 2000 always attains full cure.

Overnight cure:  Pro-Bed 2000 attains full cure in approximately 16 hours but still gives its user plenty of work time (approximately 60 to 90 minutes, depending on room temperature.)

Flowability:  Pro-Bed 2000 has the perfect consistency.  It will flow into all voids of the stock but it still stays where you put it.

Strength:  Pro-Bed 2000 uses the highest quality components such as carbon fiber and high compressive strength microscopic spheres that give the cured epoxy greater flexural and compressive strength, while completely eliminating the shrinkage problems.  There are no cheap fillers or extenders.

Carvability:  Pro-Bed 2000 is not brittle.  The cured epoxy can easily be carved, ground, or machined without softening or chipping, even in very thin sections.

Appearance:  The unique characteristics of Pro-Bed 2000 will make it easy to produce a finished product to be proud of, free of voids and surface imperfections for both the professional gunsmith and novice alike.

Clean up:  All Pro-Bed 2000 kits come with a generous amount of an extremely high quality mold release agent that is both easy to apply and easy to clean off while giving you the best possible surface finish and debonding characteristics.

For more info on Pro-Bed 2000 visit our Sister web site www.probed2000.com

Epoxy table

button probedPDF instructions

For more info on Pro-Bed 2000 visit our Sister web site www.probed2000.com


Pro Bed 2000 400 ml (13.5 oz) dual cartridge system

For large shops and manufacturers that do a lot of stock bedding, this system greatly increases speed and accuracy when dispensing Pro-Bed 2000 stock bedding epoxy. Pro-Bed 2000.  Available in either black or brown.

400ml Cart

$85.00 – Dual cartridge gun. 

This is a very high quality dual cartridge dispensing gun that will give years of service.

 

$35.00        Single 400 ml cartridge (13.5 oz) Black or Brown

$189.95      6 Pack  400 ml cartridges, (2400 ml / 81 oz)

$375.00      12 Pack  400 ml cartridges, (4800 ml / 162 oz, 1.27 Gallons)

 


Adjustable Style Bedding Pillars

Remington 700

Winchester Model 70 / Montana Model 1999

Howa Model 1500 / Weatherby Vanguard / S&W Model 1500 / Mossberg Model 1500

Made from 7075 Aluminum

Deluxe pillar kit with CD2016

Pillar bedding is fast becoming one of the most sought after modifications in the gunsmithing business.  The Score High Adjustable Style Bedding Pillars make it easy for the professional and novice alike to pillar bed a Remington 700, Winchester 70 ( Pre or Post 1964 ), or Howa Model 1500 type rifle and achieve very measurable results.  Pillars, when properly bedded into a stock, provide rigid support for the trigger guard and the receiver.  Attaching the pillars to the receiver during the bedding process insures that your pillars will not shift or rotate.  Our unique method allows the pillars to seek their own path off the action guaranteeing 100% contact and a stress free assembly.  The pillars, when firmly attached to the action, also make it possible to epoxy bed your rifle in one step instead of two.  This can knock a whole day off the pillar bedding process.  After the epoxy has cured, all of the reusable installation hardware is removed.  The pillars are then disconnected from the action, becoming a permanent part of the stock.  The Score High Adjustable Style Bedding Pillars are adjustable in .005” increments to allow precise fitting.  Included with each Deluxe and Gunsmith kit is a CD-ROM containing a Microsoft Power Point Presentation containing a 96 page installation guide with more than 100 color photos.

 

Deluxe Kit includes everything needed to properly pillar bed a rifle: Adjustable pillars, reusable installation hardware, Pro-Bed 2000 bedding epoxy (specify black or brown), mold release wax, modeling clay, and an installation guide on CD-ROM.

Gunsmith Kit includes Adjustable pillars, reusable installation hardware, and an installation guide on CD-ROM

Refill Kit includes Adjustable pillars only.

Deluxe Kit (specify black or brown):     $59.95
Gunsmith Kit:  $47.95
Refill Kit:           $24.95

button pillar kitsPDF Instruction Manuel for Pillar Bedding Kits.


button rem kits pdfPDF 95 Page Photo Rich Pillar Bedding Guide for Remington 700


button win kits pdfPDF 97 Page Photo Rich Pillar Bedding Guide for Winchester Mod 70

button howa kits pdfPDF 97 Page Photo Rich Pillar Bedding Guide for Howa 1500

 


Epoxy Bedding Supplies

 

FUMED SILICA

Fumed silica

The best method of thickening epoxy is through the use of Fumed Silica.  There are times when bedding a stock that you need the epoxy to stay exactly where you put it.  Fumed silica can be added to Pro-Bed 2000 to such an extent to make the epoxy as thick as dough with absolutely no negative effects on the finished product.  The thixotropic properties of the Fumed Silica allow for ease of mixing with the epoxy.

1 Pint container      $9.00

 

 

 

 


 

MOLD RELEASE

 WAX-0082016

The mold release agent can make or break a bedding job.  We offer a high quality industrial grade mold parting compound that is compatible for use with Pro-Bed 2000 epoxy kits.  Usually only available in large quantities, we offer it in one pint containers.

1 Pint can     $17.95

 

 

 

 

 

 


PILOTED COUNTERBORE

PCB-6252016

When pillar bedding, counter-bores work well for drilling the stock to accept the pillars.  Two sizes are available (each has a ¼” shank):

9/16” dia. for Winchesters and Howas.
5/8”  dia. for Remingtons.

Each size:    $66.95

 

 

 


 

Stock Drilling jig for Remington 700

 $249.95 for the complete set for 700s LA, SA, ADL and BDL.
$139.95 for specific models such as 700 ADL short action

 

Drill Jig Cutaway stock DJR-700

This stock drilling jig is by far the best method for drilling a Remington 700 stock to accommodate our adjustable pillars or pillars made by any one.  Each kit comes with a specially modified drill that will not split or damage the stock.  The drill bushing bar is the same diameter as a Remington action and is rigidly attached to the stock.  It is actually a superior method to drill a stock than a drill press or even a milling machine. Watch the video to see how.


Bedding Blocks for Remington 700

No more damaged finish trying to remove the factory trigger guard from a bedded stock.  No more trying to clean epoxy and mold release from the rough surface of a factory trigger guard.  Our bedding blocks leave the bedded surface of your stock looking as if it just came out of a precision mold.  Because these Bedding Blocks are made extra tall you never have to worry about the factory trigger guard being slightly below the stock’s finished surface and what to do with the epoxy that runs over the top.

Bedding Block1  Bedding Block2

$199.95 Complete set Remington 700 Long and short action BDL and Remington 700 ADL

$94.50  Remington 700 BDL Long action only (Does not include ADL Bedding Block)

$94.50  Remington 700 BDL Short action only (Does not include ADL Bedding Block)

$22.95 Remington 700 ADL long or short action


SCORE HIGH BENCH REST FOLLOWERS

Followers

Experience the pleasure of no more scratched cases, no more battered bullet noses, no more fumbling around trying to load your bolt-action rifle one round at a time.  You simply insert the Score High Bench Rest Follower in your magazine box on top of the factory follower and spring.  There it serves as a tray to hold the cartridge directly in line with the chamber for smooth, trouble free single shot loading.  This item is a must for any serious target, varmint, or silhouette shooter, or for anybody that requires the utmost accuracy from their rifle.

Mauser 98, FN 98, and Interarms Mark X Fits any type 98 Mauser actions, any caliber, standard or magnum.  Will not fit those models of the Mark X that are fitted with a magazine insert for the smaller calibers.
Remington 700 Short Fits all Remington models 700, 7, 722, and 600, chambered for small case head type cases, such as 17 Remington, 222 Remington and 223 Remington.  Also fits Howa .223
Remington 700 Medium Fits all Remington models 700, 7, 722, 600, and 660 chambered for short cartridges with standard case heads, such as the
22-250 Rem, 6mm Rem, 243 Win and 308 Win.
Remington 700 Long Fits all Remington models 700 and 721 chambered for long cartridges with either a standard or magnum case head, such as 25-06, 270 Win, 30-06 Sprg, 7mm Rem Mag, 300 Win Mag, and 375 H&H Mag.
Remington SAUM Fits all Remington models 700 and 7 chambered for the Remington Short Action Ultra Mag line of cartridges
Remington Ultra Mag Fits all Remington models 700 and 7 chambered for the Remington (Long) Ultra Mag line of cartridges
Ruger 77 PPC Fits all Ruger model 77 chambered for 6mm or 22 PPC
Ruger 77 Short Fits Ruger model 77 MK II chambered for 223 Remington.
Ruger 77 Medium # 1 Fits all Ruger models 77 and 77 MK II chambered for the 22-250 Remington.
Ruger 77 Medium # 2 Fits all regular Ruger model 77 chambered for short cartridges with standard case heads such as 220 Swift, 243 Win, 6mm Rem, 7mm X 08 Rem, and 308 Win.
Ruger 77 medium # 2 MK II Fits all Ruger model 77 MK II chambered for the short cartridges with standard case heads such as 220 Swift, 243 Win, and 308 Win.
Ruger 77 Long Fits all Ruger models 77 and 77 MK II chambered for the long and magnum cartridges such as 25-06 Rem, 30-06 Rem, 7mm Rem Mag, and 338 Win Mag. But NOT the very large rounds such as the 375 H & H or the 416 Rigby.
Savage 110 Short Fits all Savage 110 series rifles chambered for the 223 Remington based cartridges.  Fits Long or Short actions
Savage Medium Fits all Savage 110 series rifles chambered for 22-250 Rem, 243 Win, and 308 Win.  Fits Long or Short actions
Savage Long Fits all Savage 110 series rifles chambered for all long cartridges 25-06,270 Win, 30-06, 7mm Rem Mag, 300 Win Mag, and 338 Win Mag.
Savage WSM Fits all Savage 110 series rifles chambered for all Winchester Short Magnum cartridges.
Sako Short Fits all Sako models L461, AI and Browning Sako’s chambered for the small cartridges with small case heads such as 17 Rem, 222 Rem, 223 Rem, 22 PPC, and 6 PPC.
Sako Medium Fits all Sako models L579, AII and Browning Sako’s chambered for short cartridges with standard case heads such as 22-250, 243 Win, 6mm Rem, and 308 Win.  Also fits Howa .308 and Weatherby Vanguard .308
Sako Long Fits all Sako models L61R, AIII, AV and Browning Sako’s chambered for long standard or magnum cartridges such as 25-06, 270 Win, 30-06 Sprg, and 7mm Rem Mag up to 375 H&H Mag.
Winchester 70 Short Fits all post 64 Winchester Model 70 chambered for the 222 Rem and the 223 Rem.
Winchester 70 Medium # 1 Fits all post 64 Winchester Model 70 chambered for the 22-250 Rem.
Winchester 70 Medium # 2 Fits all post 64 Winchester Model 70 chambered for short cartridges with standard case heads such as 225 Win, 243 Win, and 308 Win.
Winchester 70 WSSM Fits Winchester Model 70 chambered for the Winchester Super Short magnum line of cartridges
Winchester 70 WSM Fits Winchester Model 70 chambered for the Winchester Short magnum line of cartridges (Will not fit Winchester Super Short)
Winchester 70 Long Fits all post 64 Winchester Model 70 chambered for long standard or magnum cartridges such as the 25-06, 270 Win, 30-06 Sprg, and 7mm Rem Mag up to 375 H & H Mag.
Pre 64 Winchester 70 Medium Fits all Pre 64 Winchester Model 70 chambered for the 243 Win and 308 Win. It also fits Interarms Mk X in 243 Win or those Mausers that have a magazine box fitted with a spacer to better accommodate shorter cartridges.
Pre 64 Winchester Long Fits all Pre 64 Winchester Model 70 chambered for long standard or magnum cartridges such as 270 Win, 30-06 Sprg, 7mm Rem Mag up to 375 H&H Mag.  It also fits Springfield 1903 &1903A3 in standard or magnum calibers.
Weatherby MK V Fits all Weatherby MK V up to and including the 340 Wby Mag, but NOT the 224 Weatherby Mag.
Weatherby Vanguard 1500 Series Fits all Weatherby Vanguard, Mossberg 1500, Smith & Wesson 1500, and Howa rifles chambered for standard or magnum cartridges such as 270 Win and 7mm Rem Mag.  It will not fit those chambered for  the 223 Rem.

No gunsmithing or fitting required. Each model is individually designed and engineered to fit a specific bolt-action rifle.

There are 29 models currently available.  All are machined from 6061-T6 aluminum.

For more information and model applicability, CALL TOLL FREE 1-800-326-5632.

 

$14.95 ea.  Plus $3.50 S&H per order


Single Shot Loading Block For AICS 308 Magazines

Single shot adapter for AICS 308 size Magazines. This single shot adaptor will work with any rifle/chassis that excepts AICS 308 size magazines such as but not limited to:

  • Ruger Precision Rifle
  • Magpul
  • MDT Chassis
  • J.Allen
  • McRee
  • Rock Solid
  • XLR
  • All M5 Style detachable bottom metal for AICS SA 308
  • Many more.

These blocks are CNC machined from black Delrin and utilize a very robust stainless steel latch that will never ware out.No more scratched cases, no more battered bullet noses, No more fumbling around trying to load your detachable magazine fed bolt action rifle one round at a time. You simply insert the Single Shot Magazine Block in your magazine well. There it serves as a tray that positions the cartridge directly in line with the chamber for smooth, trouble free loading. This item is a must for any serious shooter that requires the utmost accuracy from their rifle.

No gunsmithing or alteration required. simply insert the Single Shot Magazine Block just like you would your regular magazine and that’s all there is to it.

 

 

 


Extractor Riveting Tool for Remington 700, All calibers.

Flame Hardened  $69.95

Pliers Dbl Exp Lrg Pliers at work

Rivet seated       rivets

Extractor Riveting Tool for Remington 700, All calibers. Precisely secure rivet style extractors into the bolt face of any caliber using these specially designed pliers. These special clamping style pliers allow you to accurately position the extractor and keep the extractor in position while the rivet is expanded and the extractor is securely crimped into the recess of the bolt face.



Score High Gunsmithing 2016 Retail Price List

Part# Retail Product description
ERT-111 $69.95 Extractor Riveting Tool for Remington 700, All calibers
PRA-111 $59.95 Remington 700 Deluxe 7075 Aluminum Pillar bedding kit with Brown Pro-Bed 2000
PRA-112 $59.95 Remington 700 Deluxe 7075 Aluminum Pillar bedding kit with Black Pro-Bed 2000
PRA-113 $47.95 Remington 700 Gunsmith 7075 Aluminum Pillar bedding kit.
PRA-114 $24.95 Remington 700 Refill 7075 Aluminum Pillar bedding kit.
PRA-116 $134.73 Pack of 6, Remington 700 Refill 7075 Aluminum Pillar bedding kit.
PRZ-001 $11.00 Remington 700 Pillar attaching screws
PWA-111 $59.95 Winchester Model 70 Deluxe 7075 Aluminum Pillar bedding kit with Brown Pro-Bed 2000
PWA-112 $59.95 Winchester Model 70 Deluxe 7075 Aluminum Pillar bedding kit with Black Pro-Bed 2000
PWA-113 $47.95 Winchester Model 70 Gunsmith 7075 Aluminum Pillar bedding kit.
PWA-114 $24.95 Winchester Model 70 Refill 7075 Aluminum Pillar bedding kit.
PWA-116 $134.73 Pack of 6, Winchester Model 70 Refill 7075 Aluminum Pillar bedding kit.
PWZ-001 $11.00 Winchester Model 70 Pillar attaching screws
PHA-111 $59.95 Howa Model 1500 Deluxe 7075 Aluminum Pillar bedding kit with Brown Pro-Bed 2000
PHA-112 $59.95 Howa Model 1500 Deluxe 7075 Aluminum Pillar bedding kit with Black Pro-Bed 2000
PHA-113 $47.97 Howa Model 1500 Gunsmith 7075 Aluminum Pillar bedding kit.
PHA-114 $24.95 Howa Model 1500 Refill 7075 Aluminum Pillar bedding kit.
PHA-116 $134.73 Pack of 6, Howa Model 1500 Refill 7075 Aluminum Pillar bedding kit.
PHZ-001 $11.00 Howa 1500 Pillar attaching screws
PTH-428 $11.00 “T” handles 1/4 X 28 TPI used on all kits
PCB-562 $57.95 Piloted Counterbore, 9/16″ for Winchesters and Howas
PCB-625 $57.95 Piloted Counterbore, 5/8″ for Remingtons
DJR-700 $249.95 Stock Drilling jig for all Remington 700s,  LA, SA, ADL and BDL
DJR-7AL $139.95 Stock drilling jig for Remington 700 ADL Long action
DJR-7BL $139.95 Stock drilling jig for Remington 700 BDL Long action
DJR-7AS $139.95 Stock drilling jig for Remington 700 ADL Short action
DJR-7BS $139.95 Stock drilling jig Remington 700 BDL Short action
DJC-562 $72.95 9/16 Drill jig conversion kit, 2-hardend 9/16″ bushings, 1- 9/16 Drill and alignment plug
DJC-625 $72.95 5/8 Drill jig conversion kit, 2-hardend 5/8″ bushings, 1- 5/8″ Drill and alignment plug
DJR-7TL $48.95 Drill bushing holder for Remington 700 all Long actions ADL and BDL (Without bushings)
DJR-7TS $48.95 Drill bushing holder for Remington 700 all Short actions ADL and BDL (Without bushings)
DJR-BBL $48.95 Drill Jig bottom support Remington 700 BDL Long action only
DJR-BBS $48.95 Drill Jig bottom support Remington 700 BDL Short action only
DJR-7BA $48.95 Drill Jig bottom support Remington 700 ADL Long action and Short action
DJD-625 $23.00 5/8 Diameter drill for drill jig bushings
DJD-562 $23.00 9/16 Diameter drill for drill jig bushings
DJG-625 $17.50 Alignment plug for stock drilling jig 5/8 diameter
DJB-625 $42.50 One pair (2) Hardened Drill bushing  5/8 Inside diameter for drill jig
DJB-562 $42.50 One pair (2) Hardened Drill bushing  9/16 Inside diameter for drill jig
PAF-601 $14.95 .600 Dia long pillar flat Aluminum
PAF-602 $24.95 .600 Dia long pillar flat Aluminum set of 2
PAF-603 $37.95 .600 Dia long pillar flat Aluminum set of 3
EBR-004 $24.80 4 ounce Brown Pro-Bed 2000 Complete Epoxy Stock Bedding System.
EBK-004 $24.80 4 ounce Black Pro-Bed 2000 Complete Epoxy Stock Bedding System.
EBR-008 $37.20 8 ounce Brown Pro-Bed 2000 Complete Epoxy Stock Bedding System.
EBK-008 $37.20 8 ounce Black Pro-Bed 2000 Complete Epoxy Stock Bedding System.
EBR-016 $55.80 16 ounce Brown Pro-Bed 2000 Complete Epoxy Stock Bedding System.
EBK-016 $55.80 16 ounce Black Pro-Bed 2000 Complete Epoxy Stock Bedding System.
EBR-B04 $19.95 4 ounce Brown Pro-Bed 2000 Stock Bedding Epoxy, Basic Kit.
EBK-B04 $19.95 4 ounce Black Pro-Bed 2000 Stock Bedding Epoxy, Basic Kit.
EBR-B08 $24.80 8 ounce Brown Pro-Bed 2000 Stock Bedding Epoxy, Basic Kit.
EBK-B08 $24.80 8 ounce Black Pro-Bed 2000 Stock Bedding Epoxy, Basic Kit.
EBR-B16 $31.00 16 ounce Brown Pro-Bed 2000 Stock Bedding Epoxy, Basic Kit.
EBK-B16 $31.00 16 ounce Black Pro-Bed 2000 Stock Bedding Epoxy, Basic Kit.
WAX-008 $17.95 1 pint Parting Compound / Mold Release wax
PNT-720 $9.00 1 pint Fumed Silica
CLY-100 $12.50 1/4 pound modeling Clay
KNV-300 $7.50 Set of 3 Stainless Steel Mixing Knives.
STK-100 $3.65 100 Small Mixing Sticks.
STK-050 $3.65 50 Large Mixing Sticks
BBE-211 $22.95 Trigger Guard Bedding Block for Remington 700 ADL Long and Short Action
BBE-212 $94.50 Trigger Guard and Magazine Bedding Block for Remington 700 BDL Short Action
BBE-214 $94.50 Trigger Guard and Magazine Bedding Block for Remington 700 BDL Long  Action
BBE-215 $199.95 Trigger Guard and Magazine Bedding Block for Remington 700 ADL & BDL Long and Short Action
BRF-111 $14.95 Bench Rest Follower 98 Mauser
BRF-212 $14.95 Bench Rest Follower Remington 700 Short
BRF-213 $14.95 Bench Rest Follower Remington 700Medium
BRF-214 $14.95 Bench Rest Follower Remington 700 Long
BRF-215 $14.95 Bench Rest Follower Remington 700 SAUM
BRF-216 $14.95 Bench Rest Follower Remington 700 RUM
BRF-317 $14.95 Bench Rest Follower Ruger 77 PPC
BRF-318 $14.95 Bench Rest Follower Ruger 77 Short
BRF-319 $14.95 Bench Rest Follower Ruger 77 Medium # 1
BRF-320 $14.95 Bench Rest Follower Ruger 77 Medium # 2
BRF-321 $14.95 Bench Rest Follower Ruger 77 Medium # 2 MK II
BRF-322 $14.95 Bench Rest Follower Ruger 77 Long
BRF-423 $14.95 Bench Rest Follower Savage Short
BRF-424 $14.95 Bench Rest Follower Savage Medium
BRF-425 $14.95 Bench Rest Follower Savage WSM
BRF-426 $14.95 Bench Rest Follower Savage Long
BRF-527 $14.95 Bench Rest Follower Sako Short
BRF-528 $14.95 Bench Rest Follower Sako Medium
BRF-529 $14.95 Bench Rest Follower Sako Long
BRF-630 $14.95 Bench Rest Follower Winchester 70 Short
BRF-631 $14.95 Bench Rest Follower Winchester 70 Medium # 1
BRF-632 $14.95 Bench Rest Follower Winchester 70 Medium # 2
BRF-633 $14.95 Bench Rest Follower Winchester 70 WSSM
BRF-634 $14.95 Bench Rest Follower Winchester 70 WSM
BRF-635 $14.95 Bench Rest Follower Winchester 70 Long
BRF-636 $14.95 Bench Rest Follower Winchester Pre 1964 Model 70 Medium
BRF-637 $14.95 Bench Rest Follower Winchester Pre 1964 Model 70 Long
BRF-638 $14.95 Bench Rest Follower Weatherby Vanguard
BRF-639 $14.95 Bench Rest Follower Weatherby MK V